But what happens when the probe on your meat thermometer breaks? Never fear—replacing the probe on your enzoo wireless meat thermometer is a breeze, and we’ll show you how.
How to Replace the Probe on Your enzoo Wireless Meat Thermometer
Whether you’re a beginner cook just getting your feet wet in the kitchen or a seasoned pro, one thing’s for sure—no one likes overcooked meat. That’s where the enzoo wireless meat thermometer comes in handy. This little gadget allows you to check the internal temperature of your food without having to open the oven door and let all that heat out, ensuring perfectly cooked meats every time.
But what happens when the probe on your meat thermometer breaks? Never fear—replacing the probe on your enzoo wireless meat thermometer is a breeze, and we’ll show you how.
Requirements for enzoo Wireless Meat Thermometer
What You’ll Need
Before we get started, there are a few things you’ll need to gather up:
• New probe (obviously)
• Phillips head screwdriver
• A small bowl or cup
• Some distilled white vinegar
• A clean, lint-free cloth
Now that you have everything you need, let’s get started.
Instructions: Enzoo Wireless Meat Thermometer replacement
Step One: Remove the Batteries The first step is to remove the batteries from your meat thermometer. To do this, simply unscrew the battery compartment cover on the back of the unit using a Phillips head screwdriver. Once the cover is off, carefully remove the batteries and set them aside—you won’t be needing them for this particular task.
Step Two: Unscrew the Probe Cover With the battery compartment now empty, take a look at the front of the unit. You should see two small screws holding down a plastic cover over the socket where the probe attaches. Using your Phillips head screwdriver again, carefully unscrew these two screws and set them (and the cover) aside as well—we’ll be coming back to them shortly.
Read here detail about Best Wireless BBQ Thermometer
Now would be a good time to take a quick peek inside the probe socket itself to make sure there isn’t any dirt or debris build-up in there before we proceed any further. If everything looks nice and clean in there, great! If not, gently clean it out with a cotton swab or toothpick until it’s sparkling clean before moving on to step three.
Step Three: Detach the Old Probe Ok, now it’s time to remove that old probe once and for all. Gently grasp hold of the metal part of the probe (the part that goes into your food) and pull straight out—it should come right out with no resistance. If it doesn’t budge, try wiggling it a bit until it loosens up and slides right out.
Step Four: Insert New Probe With Old Probe now successfully removed, go ahead and grab your new probe and line up the metal end with its respective socket on the front of your device . . . but don’t push it all way in just yet! Before we do that, we need to calibrate this bad boy first so it gives us accurate readings going forward. Calibrating Your New Probe To calibrate your new probe, all you need is a small bowl or cup of ice water and some distilled white vinegar. Fill up your vessel of choice with ice until it’s about halfway full, then pour in enough vinegar until liquid covers at least two-thirds of an ice cube—this will help ensure an accurate reading later on down line. Next, insert your new probe into this mixture until only about an inch or so of metal is still showing outside of the liquid . . . then wait about 10 seconds or so for it to adjust itself before removing completely. Finally, dry off any excess moisture from both sides of your new probe with a clean cloth before inserting into its socket on your device as far as it will go—you should hear/feel a gentle click when it’s seated correctly. At this point, you can go ahead and reattach those two screws (but don’t overtighten!) as well as that plastic cover over top before moving on to step five . . .
Step Five: Reattach Batteries With everything now calibrated and put back together correctly, go ahead and reinsert those batteries back into their rightful place before replacing that battery cover and giving it a good screwing (but not too tight!). All done! And there you have it—a quick and easy guide to replacing that pesky broken probe on your enzoo wireless meat thermometer like a pro! Happy cooking!